IFM Electronic efector300 SU9004 Operating Instructions Manual Download Page 20

Page: 20 / 23

10.4.8 Select the medium to be monitored

►

Select [MEDI] and set the requested medium:

-[H2O] = water�

-[GLYC] = glycol solutions�

-[OIL�1] = high viscosity oil (30��68 mm²/s at 40°C; 30��68 cSt at 104°F)

-[OIL�2] = low viscosity oil (7��40 mm²/s at 40°C; 7��40 cSt at 104°F)

10.5 Service functions
10.5.1 Read min/max values for volumetric flow

►

Select [HI�F] or [Lo�F], briefly press [Set]�

[HI�F] = max� value, [LO�F] = min� value�

Delete memory:

►

Select [HI�F] or [LO�F]�

►

Press and hold [Set] until [----] is displayed�

►

Briefly press [Mode/Enter]�

It makes sense to delete the memories as soon as the unit operates under

normal operating conditions for the first time�

10.5.2 Read the min/max values for the temperature

►

Select [HI�T] or [Lo�T], briefly press [Set]�

[HI�T] = max� value, [LO�T] = min� value�

Delete memory:

►

Select [HI�T] or [LO�T]�

►

Press and hold [Set] until [----] is displayed�

►

Briefly press [Mode/Enter]�

It makes sense to delete the memories as soon as the unit operates under

normal operating conditions for the first time�

10.5.3 Reset all parameters to factory setting

►

Select [rES]�

►

Press and hold [Set] until [----] is displayed�

►

Briefly press [Mode/Enter]�

For the factory settings please refer to the end of these instructions (→ 13

Factory setting)�

We recommend taking down your own settings in that table before carrying

out a reset�

Summary of Contents for efector300 SU9004
























Search results

Summary of Contents for efector300 SU9004

Reviews:

Related manuals for efector300 SU9004

Brands by name

Popular brands

IFM Electronic efector300 SU9004, Operating Instructions Manual

Search results

Summary of Contents for efector300 SU9004

Reviews:

Related manuals for efector300 SU9004

Brands by name

Popular brands