IFM Electronic AL1121 Operating Instructions Manual Download

Page: 63 / 109

ifm

Operating Instructions IO-Link Master with EtherNet/IP interface StandardLine 4 Ports IP 69K (AL1121)

2017-05-31

Appendix

12.1.6

Interfaces

22630

Interfaces

Communication interface

Ethernet; IO-Link

Communication interface

IO-Link; TCP/IP; PROFINET IO

Ethernet

Transmission standard

10Base-T; 100Base-TX

Transmission rate

10; 100

Protocol

TCP/IP; PROFINET IO

Factory settings



IP address: 192.168.1.250



Subnet mask: 255.255.255.0



Gateway IP address: 0.0.0.0



MAC address: see type label

IO-Link Master

Transmission type

COM 1 / COM 2 / COM 3

IO-Link revision

V1.1

Number of ports class A

12.1.7

Operating conditions

22823

Operating conditions

Applications

Indoor use

Ambient temperature [°C]

-25...60

Storage temperature [°C]

-25...85

Max. perm. relative air humidity [%]

Max. height above sea level [m]

2000

Protection rating

IP 65; IP 67; IP 69K; (operation with stainless steel protective caps: IP 69K)

Pollution Degree

12.1.8

Approvals / tests

22824

Approval / tests

EMC



EN 61000-6-2



EN 61000-6-4

MTTF [Years]

Summary of Contents for AL1121














































































































Search results

Summary of Contents for AL1121

Reviews:

Related manuals for AL1121

Brands by name

Popular brands

IFM Electronic AL1121, Operating Instructions Manual

Search results

Summary of Contents for AL1121

Reviews:

Related manuals for AL1121

Brands by name

Popular brands