IFM Electronic AL1121 Operating Instructions Manual Download

Page: 53 / 109

ifm

Operating Instructions IO-Link Master with EtherNet/IP interface StandardLine 4 Ports IP 69K (AL1121)

2017-05-31

Operation

9.1.1

Web interface: Read device and diagnostic information

12744

In order to read the diagnostic information about the current device status via the web interface:
►

Connect laptop/PC and AL1121 via the Ethernet internet.

►

Start web browser.

►

Enter the following into the address field of the browser: and confirm with [ENTER]:

Web browser shows the web interface of the device.

The page shows the following data:



Table with connected IO-Link devices

Name

Description

[Port]

Number of the IO-Link interface

[Mode]

Operating mode of the IO-Link interface

[Comm. Mode]

Baud rate of the IO-Link interface

[MasterCycleTime]

Cycle time

[Vendor ID]

ID of the manufacturer of the IO-Link device

[Device ID]

ID of the IO-Link device

[Name]

Article number of the IO-Link device



For ifm articles: This article number is stored along with a link to the produkt page on
the ifm website.

[Serial]

Serial number of the IO-Link device

[LR Interval]

Cycle time for the communication with the SmartObserver



Version information of the installed firmware components

Name

Description

[Firmware version]

Firmware version

[FirmwareCN Version]

Version of the firmware container

[Bootloader Version]

Version of the boot loader

[NETX Firmware Version]

Version of the EtherNet/IP firmware



Diagnostic information of the device

Name

Description

[Current]

Current (in mA)

[Voltage]

Voltage (in mV)

[Short Circuit]

Number of detected short circuits

[Temperature]

Device temperature (in °C)

The page of the device is constantly updated. This is why the data is always up-to-date.

Summary of Contents for AL1121














































































































Search results

Summary of Contents for AL1121

Reviews:

Related manuals for AL1121

Brands by name

Popular brands

IFM Electronic AL1121, Operating Instructions Manual

Search results

Summary of Contents for AL1121

Reviews:

Related manuals for AL1121

Brands by name

Popular brands