IFM Electronic AL1121 Operating Instructions Manual Download

Page: 15 / 109

ifm

Operating Instructions IO-Link Master with EtherNet/IP interface StandardLine 4 Ports IP 69K (AL1121)

2017-05-31

Function

4.2

Digital inputs

7584

The device has 4 digital inputs (type 2 according to EN 61131-2).

The digital inputs are on pin 2 of the IO-Link ports X01 ... X04.

All inputs refer to the potential of the device supply (pin 3).

4.3

IO-Link supply

7623

The device has 4 supplies for IO-Link devices (sensors, actuators).

The IO-Link ports X01...X04 are ports class A.

Every supply provides short circuit monitoring.

The device ensures fire protection for the connected IO-Link devices by providing a power-restricted
circuit at the IO-Link ports (according to IEC61010-1).

Summary of Contents for AL1121














































































































Search results

Summary of Contents for AL1121

Reviews:

Related manuals for AL1121

Brands by name

Popular brands

IFM Electronic AL1121, Operating Instructions Manual

Search results

Summary of Contents for AL1121

Reviews:

Related manuals for AL1121

Brands by name

Popular brands