IEM Tel-O-Graph BT Instructions For Use Manual Download Page 46

Page: 46 / 54

Technical data and symbols

Technical data

The blood pressure monitor complies with the EMC directives.
The blood pressure cuff and air hose are made of a non-conductive material. This makes the device defibrillator
safe.

Specification

Value

Unit

Measuring method

Oscillometric

Blood pressure
measurement range

Systolic

60 to 290

Diastolic

30 to 195

mmHg

Pulse measurement range

30 to 240

1/min

Pressure Accuracy

±2% or ±3 mmHg, whichever is greater

Memory (without PWA)

350

Measurements

Memory (with PWA)

Measurements

Power supply

4-6 VDC (4x NiMH or LR6, AA)

Dimensions (L x W x H)

151 X 108 X 57

Weight (without batteries)

334

Material (housing)

ABS (acrylonitrile-butadiene-styrene)

Material (cuff)

Polyester

IP protection class

Operating temperature

+5 to +40

°C

Summary of Contents for Tel-O-Graph BT























































Search results

Summary of Contents for Tel-O-Graph BT

Reviews:

Related manuals for Tel-O-Graph BT

Brands by name

Popular brands

IEM Tel-O-Graph BT, Instructions For Use Manual

Search results

Summary of Contents for Tel-O-Graph BT

Reviews:

Related manuals for Tel-O-Graph BT

Brands by name

Popular brands