IEI Technology WSB-H810 User Manual Download Page 97

Page: 97 / 165

WSB-H810 PICMG 1.0 CPU Card

Page 83

5.3.6 USB Configuration

Use the

USB Configuration

menu (

BIOS Menu 8

) to read USB configuration information

and configure the USB settings.

Advanced

USB Configuration

USB Devices:
1 Keyboard, 2 Hubs

Legacy USB Support

[Enabled]

Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
---------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 8: USB Configuration

USB Devices

The

USB Devices

field lists the USB devices that are enabled on the system

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB

keyboard can control the system even when there is no USB driver loaded onto the system.

Enabled D

EFAULT

Legacy USB support enabled

Disabled

Legacy USB support disabled

Auto

Legacy USB support disabled if no USB devices are

connected

Summary of Contents for WSB-H810






































































































































































Search results

Summary of Contents for WSB-H810

Reviews:

Related manuals for WSB-H810

Brands by name

Popular brands

IEI Technology WSB-H810, User Manual

Search results

Summary of Contents for WSB-H810

Reviews:

Related manuals for WSB-H810

Brands by name

Popular brands