manualshive.com logo in svg

IEI Technology WAFER-945GSELVDS2-N270-R10, User Manual

Share
Download
IEI Technology WAFER-945GSELVDS2-N270-R10 User Manual Download Page 108

 

 

WAFER-945GSELVDS2

Page 96 

ƒ

 

Emulation Type [Auto] 

Use the 

Emulation Type

 BIOS option to specify the type of emulation BIOS has to 

provide for the USB device. 

Î

 

Auto D

EFAULT

 

BIOS auto-detects the current USB. 

Î

 

Floppy  

The USB device will be emulated as a floppy drive. 

The device can be either A: or B: responding to 

INT13h calls that return DL = 0 or DL = 1 

respectively. 

Î

 

Forced FDD 

 

Allows a hard disk image to be connected as a 

floppy image. This option works only for drives 

formatted with FAT12, FAT16 or FAT32. 

Î

 

Hard Disk 

 

Allows the USB device to be emulated as hard disk 

responding to INT13h calls that return DL values of 

80h or above. 

Î

 

CDROM  

Assumes the CD-ROM is formatted as bootable 

media. All the devices that support block sizes 

greater than 512 bytes can only be booted using this 

option. 

Summary of Contents for WAFER-945GSELVDS2-N270-R10













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands