IEI Technology tKINO-AL User Manual Download Page 110

Page: 110 / 136

tKINO-AL SBC

Page 96



Quiet Boot [Enabled]

Use the

Quiet Boot

BIOS option to select the screen display when the system boots.



Disabled

Normal POST messages displayed



Enabled D

EFAULT

OEM Logo displayed instead of POST messages



Launch PXE OpROM [Disabled]

Use the

Launch PXE OpROM

option to enable or disable boot option for legacy network

devices.



Disabled D

EFAULT

Ignore all PXE Option ROMs



Enabled

Load PXE Option ROMs.



Option ROM Messages [Force BIOS]

Use the

Option ROM Messages

option to set the Option ROM display mode.



Force

BIOS

EFAULT

Sets display mode to force BIOS.



Keep

Current

Sets display mode to current.



UEFI Boot [Disabled]

Use the

UEFI Boot

option to enable or disable to boot from the UEFI devices.



Enabled

Boot from UEFI devices is enabled.



Disabled D

EFAULT

Boot from UEFI devices is disabled.



Boot Option Priority

Use the

Boot Option Priority

function to set the system boot sequence from the available

devices. The drive sequence also depends on the boot sequence in the individual device

section.

Summary of Contents for tKINO-AL









































































































































Search results

Summary of Contents for tKINO-AL

Reviews:

Brands by name

Popular brands

IEI Technology tKINO-AL, User Manual

Search results

Summary of Contents for tKINO-AL

Reviews:

Brands by name

Popular brands