IEI Technology TANK-880-Q370 Series User Manual Download Page 46

Page: 46 / 120

TANK-880-Q370

Page 36

4.2.1 Clear CMOS Switch (J_CMOS1)

PIN NO.

DESCRIPTION

Open

Normal Operation (Default)

Push

Clear CMOS Setup

Table 4

‑

2: Clear CMOS Switch (J_CMOS1)

4.2.2 AT/ATX Mode Switch (J_AT_ATX1)

4.2.3 BIOS Programming Connector (JSPI1)

PIN NO. DESCRIPTION

VCC3V

MISO

CLK

MOSI

GND

Table 4

‑

4: BIOS Programming Connector Pinouts (JSPI1)

4.2.4 RS-232 Pin Header (COM4)

PIN NO. DESCRIPTION

PIN NO.

DESCRIPTION

NDCD4

NDSR4

NRX4

NRTS4

NTX4

NCTS4

NDTR4

NRI4

GND

Table 4

‑

5: RS-232 Pin Header (COM4)

PIN NO.

DESCRIPTION

Short 1 - 2

ATX Mode (default)

Short 2- 3

AT Mode

Table 4

‑

3: AT/ATX Mode Switch (J_AT_ATX1)

Summary of Contents for TANK-880-Q370 Series

























































































































Search results

Summary of Contents for TANK-880-Q370 Series

Reviews:

Related manuals for TANK-880-Q370 Series

Brands by name

Popular brands

IEI Technology TANK-880-Q370 Series, User Manual

Search results

Summary of Contents for TANK-880-Q370 Series

Reviews:

Related manuals for TANK-880-Q370 Series

Brands by name

Popular brands