IEI Technology TANK-870AI SERIES User Manual Download

Page: 64 / 137

TANK-870AI Embedded System

Page 50

4.3.1 Audio Jack (JAUDIO1)

PIN NO. DESCRIPTION

PIN NO.

DESCRIPTION

GND

ILMIC1-CONN-L

GND

IJD_MIC

ILMIC1-CONN-R

ILFRONT-L

GND

IJD_FRONT

ILFRONT-R

Table 4-15: Audio Jack Pinouts (JAUDIO1)

4.3.2 DIO connector (DIO1)

PIN NO. DESCRIPTION

PIN NO.

DESCRIPTION

DIN0

DOUT0

DIN1

DOUT1

DIN2

DOUT2

DIN3

DOUT3

+5V

Table 4-16: DIO connector Pinouts (DIO1)

4.3.3 Ethernet and USB 2.0 Connectors (LAN1_USB1)

PIN

DESCRIPTION

PIN

DESCRIPTION

USBV7L

DATA7_N

DATA7_P

IO_GND

USBV7L

DATA8_N

DATA8_P

IO_GND

Table 4-17: USB 2.0 Port Pinouts (USB1)

PIN

DESCRIPTION

PIN

DESCRIPTION

GND

ILAN_MDI0_DP

ILAN_MDI0_DN

ILAN_MDI1_DP

ILAN_MDI1_DN

ILAN_MDI2_DP

ILAN_MDI2_DN

ILAN_MDI3_DP

Summary of Contents for TANK-870AI SERIES










































































































































Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands

IEI Technology TANK-870AI SERIES, User Manual

Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands