IEI Technology TANK-870AI SERIES User Manual Download

Page: 61 / 137

TANK-870AI Embedded System

Page 47

DPD_OB_LANE1_N_C

VCC3

GND

Table 4-6: DisplayPort connector Pinouts (DP1)

4.2.6 EC Debug Connector (CN4)

PIN NO. DESCRIPTION

PIN NO.

DESCRIPTION

KSI0

KSO9

KSO0

KSO10

KSO1

KSO12

KSO2

KSI1

KSO3

KSO11

KSO4

KSI2

KSO5

KSI3

KSO6

GND

KSO7

GND

KSO8

GND

Table 4-7: EC Debug Connector Pinouts (CN4)

4.2.7 EC Programming Connector (JSPI2)

PIN NO. DESCRIPTION

+V3.3M_SPI_CON_EC

SPI_CS#0_CN_EC

SPI_SO_SW_EC

SPI_CLK_SW_EC

SPI_SI_SW_EC

GND

Table 4-8: EC Programming Connector Pinouts (JSPI2)

4.2.8 Keyboard and mouse connector (KB_MS1)

PIN NO. DESCRIPTION

VCC5_KBMS

MSDATA

MSCLK

KBDATA

KBCLOCK

KBGND

Table 4-9: Keyboard and mouse connector Pinouts (KB_MS1)

Summary of Contents for TANK-870AI SERIES










































































































































Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands

IEI Technology TANK-870AI SERIES, User Manual

Search results

Summary of Contents for TANK-870AI SERIES

Reviews:

Related manuals for TANK-870AI SERIES

Brands by name

Popular brands