manualshive.com logo in svg

IEI Technology SPCIE-C2260-i2, User Manual, Page: 79 / 162

Share
Download
IEI Technology SPCIE-C2260-i2 User Manual Download Page 79

 

 

SPCIE-C2260-i2 PICMG 1.3 CPU Card 

Page 63 

Step 4: 

Seat the iRIS-2400 module

. Gently push downwards and the arms clip into 

place (

Figure 4-12

).

 

Step 0:

 

  NOTE: 

After installing the iRIS-2400 module, use 

LAN2

  port to establish a 

network connection. Please refer to 

Section  4.7

  for IPMI setup 

procedures. 

4.5.3 SATA Drive Connection 

The SPCIE-C2260-i2 is shipped with two SATA drive cables. To connect the SATA drives 

to the connectors, please follow the steps below. 

Step 1: 

Locate the connectors

. The locations of the SATA drive connectors are shown 

in 

Chapter 3

. 

Step 2: 

Insert the cable connector

. Insert the cable connector into the on-board SATA 

drive connector until it clips into place. See 

Figure 4-13

. 

 

Figure 4-13: SATA Drive Cable Connection 

Summary of Contents for SPCIE-C2260-i2



































































































































































Reviews:

No comments