IEI Technology SPCIE-C2260-i2 Page 149 User Manual Download

Page: 149 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 133

D.1 Introduction

The DIO connector on the SPCIE-C2260-i2 is interfaced to GPIO ports on the Super I/O

chipset. The digital inputs and digital outputs are generally control signals that control the

on/off circuit of external devices or TTL devices. Data can be read or written to the

selected address to enable the DIO functions.

NOTE:

For further information, please refer to the datasheet for the Super I/O

chipset.

The BIOS interrupt call

INT 15H

controls the digital I/O.

INT 15H:

AH – 6FH
Sub-function:
AL – 8

:Set the digital port as INPUT

:Digital I/O input value

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands