IEI Technology SPCIE-C2260-i2 Page 102 User Manual Download

Page: 102 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 86

5.3.8 USB Configuration

Use the

USB Configuration

menu (

BIOS Menu 10

) to read USB configuration

information and configure the USB settings.

Advanced

USB Configuration

USB Devices:
1 Keyboard, 2 Hubs

Legacy USB Support

[Enabled]

Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.

---------------------



: Select Screen

↑

↓

: Select Item

Enter:  Select
+/-:  Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 10: USB Configuration



USB Devices

The

USB Devices

field lists the USB devices that are enabled on the system



Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB

keyboard can control the system even when there is no USB driver loaded onto the

system.



Enabled

EFAULT

Legacy USB support enabled

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands