IEI Technology PICOe-9452 User Manual Download Page 99

Page: 99 / 250

PICOe-9452 Half-size CPU Card

Page 81

Keyboard

Mouse

RS-232 serial communications device

5.3 CPU, CPU Cooling Kit and DIMM Installation

WARNING:

A CPU should never be turned on without the specified cooling kit

being installed. If the cooling kit (heat sink and fan) is not properly

installed and the system turned on, permanent damage to the CPU,

PICOe-9452 and other electronic components attached to the system

may be incurred. Running a CPU without a cooling kit may also result

in injury to the user.

The CPU, CPU cooling kit and DIMM are the most critical components of the PICOe-9452.

If one of these component is not installed the PICOe-9452 cannot run.

5.3.1 Socket M CPU Installation

WARNING:

CPUs are expensive and sensitive components. When installing the

CPU please be careful not to damage it in anyway. Make sure the CPU

is installed properly and ensure the correct cooling kit is properly

installed.

To install a Socket M CPU onto the PICOe-9452, follow the steps below:

Summary of Contents for PICOe-9452



























































































































































































































































Search results

Summary of Contents for PICOe-9452

Reviews:

Related manuals for PICOe-9452

Brands by name

Popular brands

IEI Technology PICOe-9452, User Manual

Search results

Summary of Contents for PICOe-9452

Reviews:

Related manuals for PICOe-9452

Brands by name

Popular brands