IEI Technology PICOe-9452 User Manual Download Page 148

Page: 148 / 250

PICOe-9452 Half-size CPU Card

Page 130

and the parallel port device and the transmission

rates between the two are much faster than the

Normal mode.



ECP

The parallel port operates in the extended

capabilities port (ECP) mode. The ECP mode

supports bi-directional communication between the

system and the parallel port device and the

transmission rates between the two are much faster

than the Normal mode



ECP+EPP

The parallel port is compatible with ECP and EPP

devices described above



Parallel Port IRQ [IRQ7]

Use the

Parallel Port IRQ

option to set the parallel port interrupt address.



IRQ5

IRQ5 is assigned as the parallel port interrupt address



IRQ7 D

EFAULT

IRQ7 is assigned as the parallel port interrupt address

6.3.4 Hardware Health Configuration

The

Hardware Health Configuration

menu (

BIOS Menu 7

) shows the operating

temperature, fan speeds and system voltages.

Summary of Contents for PICOe-9452



























































































































































































































































Search results

Summary of Contents for PICOe-9452

Reviews:

Related manuals for PICOe-9452

Brands by name

Popular brands

IEI Technology PICOe-9452, User Manual

Search results

Summary of Contents for PICOe-9452

Reviews:

Related manuals for PICOe-9452

Brands by name

Popular brands