IEI Technology PCISA-LX User Manual Download Page 127

Page: 127 / 214

Page 127

PCISA -LX CPU Card

x ACPI Function [Disabled]

The

ACPI Function

is enabled when the

Power Management

option is set to ACPI;

otherwise, it is disabled.

Disabled

EFAULT

ACPI function disabled

Enabled

ACPI function enabled

ACPI Suspend Type [S1 (POS)]

The

ACPI Suspend Type

BIOS option specifies the sleep state the system enters when

not being used. Set to S1(POS), the system appears off, the CPU is stopped, RAM is

refreshed, and the system is running in a low power mode. This item is not configurable.

Power Management [APM]

Use the

Power Management

option to set the power management type used by the

system.

Disabled

All power management options are turned off. The only

user configurable options are the power button and

alarm settings.

Legacy

Standby and suspend modes can be set.

APM

EFAULT

Advanced power management (APM) is activated

ACPI

Advanced Configuration and Power Interface (ACPI) is

activated.

x Standby Mode [Disabled]

The

Standby Mode

option can only be selected if the

Power Management

option is set

Legacy

. The

Standby Mode

specifies the amount of time the system can be inactive

before the system enters standby mode. The

Standby Mode

options are:

Summary of Contents for PCISA-LX























































































































































































































Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands

IEI Technology PCISA-LX, User Manual

Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands