IEI Technology PCISA-LX User Manual Download Page 100

Page: 100 / 214

Page 100

IEI® Technology, Corp

PCISA-LX CPU Card

Auto

EFAULT

Setting this option allows the device to be automatically

detected by the BIOS.

Manual

Selecting this option allows manual configuration of the

device on the IDE channel in BIOS.

Access Mode [Auto]

The

Access Mode

option can only be configured if the

IDE Primary Master

is set to

either

Manual

Auto

. Use the

Access Mode

option to determine the hard disk BIOS

translation modes. Most systems now use hard drives with large capacities and therefore

either the LBA translation mode or auto mode should be selected.

CHS

Select this mode if the HDD capacity is less than

504MB.

LBA

Select this mode if the HDD capacity is more than

8.4GB.

Large

This mode is an extended ECHS mode and while it

supports HDDs larger than 504MB, it is not

recommended.

Auto

EFAULT

If you are unsure of what access mode to set, select this

option.

Capacity

The

Capacity

specification indicates the storage capacity of the HDD installed in the

system.

Cylinder

The

Cylinder

specification indicates how many cylinders (tracks) are on the HDD installed

in the system.

Summary of Contents for PCISA-LX























































































































































































































Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands

IEI Technology PCISA-LX, User Manual

Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands