IEI Technology PCISA-9652 User Manual Download Page 97

Page: 97 / 232

PCISA -9652 Half-Size CPU Card

Page 77

5.3 CPU, CPU Cooling Kit and DIMM Installation

WARNING:

A CPU should never be turned on without the specified cooling kit

being installed. If the cooling kit (heat sink and fan) is not properly

installed and the system turned on, permanent damage to the CPU,

PCISA-9652 and other electronic components attached to the system

may be incurred. Running a CPU without a cooling kit may also result

in injury to the user.

The CPU, CPU cooling kit and DIMM are the most critical components of the PCISA-9652.

If one of these component is not installed the PCISA-9652 cannot run.

5.3.1 Socket P CPU Installation

WARNING:

CPUs are expensive and sensitive components. When installing the

CPU please be careful not to damage it in anyway. Make sure the CPU

is installed properly and ensure the correct cooling kit is properly

installed.

To install a socket P CPU onto the PCISA-9652, follow the steps below:

WARNING:

When handling the CPU, only hold it on the sides. DO NOT touch the

pins at the bottom of the CPU.

Step 1:

Unlock the CPU retention screw.

When shipped, the retention screw of the

Summary of Contents for PCISA-9652









































































































































































































































Search results

Summary of Contents for PCISA-9652

Reviews:

Related manuals for PCISA-9652

Brands by name

Popular brands

IEI Technology PCISA-9652, User Manual

Search results

Summary of Contents for PCISA-9652

Reviews:

Related manuals for PCISA-9652

Brands by name

Popular brands