IEI Technology PCISA-9652 User Manual Download Page 110

Page: 110 / 232

PCISA-9652 Half-Size CPU Card

Page 90

5.5 Chassis Installation

5.5.1 Airflow

WARNING:

Airflow is critical to the cooling of the CPU and other onboard

components. The chassis in which the PCISA-9652 must have air

vents to allow cool air to move into the system and hot air to move out.

The PCISA-9652 must be installed in a chassis with ventilation holes on the sides allowing

airflow to travel through the heat sink surface. In a system with an individual power supply

unit, the cooling fan of a power supply can also help generate airflow through the board

surface.

NOTE:

IEI has a wide range of backplanes available. Please contact your

PCISA-9652 vendor, reseller or an IEI sales representative at

[email protected]

or visit the IEI website (

http://www.ieiworld.com.tw

)

to find out more about the available chassis.

5.5.2 Backplane Installation

Before the PCISA-9652 can be installed into the chassis, a backplane must first be

installed. Please refer to the installation instructions that came with the backplane and the

chassis to see how to install the backplane into the chassis.

Summary of Contents for PCISA-9652









































































































































































































































Search results

Summary of Contents for PCISA-9652

Reviews:

Related manuals for PCISA-9652

Brands by name

Popular brands

IEI Technology PCISA-9652, User Manual

Search results

Summary of Contents for PCISA-9652

Reviews:

Related manuals for PCISA-9652

Brands by name

Popular brands