IEI Technology PCIE-H610 Page 83 User Manual Download

Page: 83 / 140

PCIE-H610 PICMG 1.3 CPU Card

Page 70

5.3.6 USB Configuration

Use the

USB Configuration

menu (

BIOS Menu 9

) to read USB configuration information

and configure the USB settings.

Advanced

USB Configuration

USB Devices:
2 Hubs

USB Support

[Enabled]

Legacy USB Support

[Enabled]

USB Support Parameters

---------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 9: USB Configuration

USB Devices

The

USB Devices Enabled

field lists the USB devices that are enabled on the system

USB Support [Enabled]

Use the

USB Support

option to enable or disable USB support on the system.

Disabled

USB support disabled

Enabled D

EFAULT

USB support enabled

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB

Summary of Contents for PCIE-H610













































































































































Search results

Summary of Contents for PCIE-H610

Reviews:

Related manuals for PCIE-H610

Brands by name

Popular brands

IEI Technology PCIE-H610, User Manual

Search results

Summary of Contents for PCIE-H610

Reviews:

Related manuals for PCIE-H610

Brands by name

Popular brands