IEI Technology PCIE-H610 Page 20 User Manual Download

Page: 20 / 140

PCIE-H610 PICMG 1.3 CPU Card

Page 7

1.7 Technical Specifications

The PCIE-H610 technical specifications are listed below.

Specification/Model PCIE-H610

Form Factor

PICMG 1.3

CPU Supported

LGA1155 Intel® Core™ i7/i5/i3/Pentium®/Celeron® CPU

PCH

Intel® H61

Memory

Two 240-pin 1333/1066 MHz dual-channel unbuffered DDR3/DDR3L

(1.35V) SDRAM DIMMs support (system max. 16.0 GB)

Graphics Engine

Intel® HD Graphics 2000/3000

Supports DirectX 10.1 and OpenGL 3.0

Full MPEG2, VC1, AVC Decode

Audio

Supports IEI AC-KIT-892HD audio kit

BIOS

UEFI BIOS

B222ARxx supports four PCIe x1 slots (default)

V34QARxx supports one PCIe x4 slot

Ethernet Controllers

Dual Realtek RTL8111E PCIe GbE Ethernet controller (LAN1 with

ASF 2.0 support)

Super I/O Controller

Fintek F81866

Watchdog Timer

Software programmable supports 1~255 sec. system reset

Expansions

4 x PCI link via golden finger

16-lane PCIe link from CPU via golden finger:

Support one PCIe x16 slot on the backplane

4-lane PCIe link from PCH via golden finger:

Support either one PCIe x4 slot or four PCIe x1 slots on the backplane

For installing the PCIe x4 device on the backplane, the user must

update BIOS to the version which supports one PCIe x4 slot

I/O Interface Connectors

Audio Connector

One internal audio connector (10-pin header)

Digital I/O

8-bit digital I/O

Summary of Contents for PCIE-H610













































































































































Search results

Summary of Contents for PCIE-H610

Reviews:

Related manuals for PCIE-H610

Brands by name

Popular brands

IEI Technology PCIE-H610, User Manual

Search results

Summary of Contents for PCIE-H610

Reviews:

Related manuals for PCIE-H610

Brands by name

Popular brands