IEI Technology PCIE-9450 User Manual Download Page 204

Page: 204 / 232

PCIE-9450 PICMG 1.3 CPU Card

Page 184

E.1 Introduction

The Intel® ICH9DO chipset can provide data protection for serial ATA (SATA) disks via

the Intel® Matrix Storage Manager using one of three fault-tolerant RAID levels: RAID 1, 5

or 10. When using two hard drives, matrix RAID allows RAID 0 and RAID 1 functions to be

combined, where critical files can be stored on RAID 1, and RAID 0 can be used for

non-critical items such as software. RAID 5 and RAID 0 can be combined to provide

higher performance, capacity, and fault tolerance.

CAUTION!

A configured RAID volume (which may consist of multiple hard drives) appears

to an operating system as a contingent storage space. The operating system

will not be able to distinguish the physical disk drives contained in a RAID

configuration.

E.1.1 Precautions

One key benefit a RAID configuration brings is that a single hard drive can fail within a

RAID array without damaging data. With RAID1 array, a failed drive can be replaced and

the RAID configuration restored.

WARNING!

Irrecoverable data loss occurs if a working drive is removed when trying to

remove a failed drive. It is strongly recommended to mark the physical

connections of all SATA disk drives. Drive locations can be identified by

attaching stickers to the drive bays. If a drive member of a RAID array should

fail, the failed drive can then be correctly identified.

Summary of Contents for PCIE-9450









































































































































































































































Search results

Summary of Contents for PCIE-9450

Reviews:

IEI Technology PCIE-9450, User Manual, Page: 204 / 232

Search results

Summary of Contents for PCIE-9450

Reviews: