IEI Technology Nova-lx User Manual Download

Page: 127 / 225

NOVA-LX 5.25” Motherboard

Page 107

BIOS Menu 5: IDE Master and IDE Slave Configuration

Auto-Detected Drive Parameters

The “grayed-out” items in the left frame are IDE disk drive parameters automatically

detected from the firmware of the selected IDE disk drive. The drive parameters are listed

as follows:

Device

: Lists the device type (e.g. hard disk, CD-ROM etc.)

Type

: Indicates the type of devices a user can manually select

Vendor

: Lists the device manufacturer

Size

: List the storage capacity of the device.

LBA Mode

: Indicates whether the LBA (Logical Block Addressing) is a

method of addressing data on a disk drive is supported or not.

Block Mode

: Block mode boosts IDE drive performance by increasing the

amount of data transferred. Only 512 bytes of data can be transferred per

Summary of Contents for Nova-lx


































































































































































































































Search results

Summary of Contents for Nova-lx

Reviews:

Related manuals for Nova-lx

Brands by name

Popular brands

IEI Technology Nova-lx, User Manual

Search results

Summary of Contents for Nova-lx

Reviews:

Related manuals for Nova-lx

Brands by name

Popular brands