IEI Technology NANO-ULT5 User Manual Download Page 86

Page: 86 / 147

NANO-ULT5 SBC

Page 72

Figure 4-21: Single RS-232 Cable Installation

Step 3:

Secure the bracket

. The single RS-232 connector has two retention screws

that must be secured to a chassis or bracket.

Step 4:

Connect the serial device

. Once the single RS-232 connector is connected to

a chassis or bracket, a serial communications device can be connected to the

system.

Step 0:

4.9.4 SATA Drive Connection

The NANO-ULT5 is shipped with a SATA drive cable. To connect the SATA drive to the
connector, please follow the steps below.

Step 1:

Locate the SATA connector and the SATA power connector.

The locations of

the connectors are shown in

Chapter 3

Step 2:

Insert the cable connector

. Insert the cable connector into the on-board SATA

drive connector and the SATA power connector. See

Figure 4-22

Summary of Contents for NANO-ULT5




















































































































































Search results

Summary of Contents for NANO-ULT5

Reviews:

Related manuals for NANO-ULT5

Brands by name

Popular brands

IEI Technology NANO-ULT5, User Manual

Search results

Summary of Contents for NANO-ULT5

Reviews:

Related manuals for NANO-ULT5

Brands by name

Popular brands