IEI Technology NANO-ULT5 User Manual Download Page 21

Page: 21 / 147

NANO-ULT5 SBC

Page 7

1.7 Technical Specifications

NANO-ULT5 technical specifications are listed below.

Specification

NANO-ULT5

SoC

generation Intel

mobile ULT on-board SoC:



Intel

Core™ i7-8665UE on-board SoC

(1.9 GHz, quad-core, 8 MB cache, TDP=15 W)



Intel

Core™ i5-8365UE on-board SoC

(1.6 GHz, quad-core, 6 MB cache, TDP=15 W)



Intel

Core™ i3-8145UE on-board SoC

(2.1 GHz, dual-core, 4 MB cache, TDP=15 W)



Intel

Celeron

4305UE on-board SoC

(2.2 GHz, dual-core, 2 MB cache, TDP=15 W)

BIOS

AMI UEFI BIOS

Memory

Two 260-pin 2133/2400 MHz dual-channel DDR4 SO-DIMM
slots (system max. 32 GB)

Graphics

generation Intel

HD Graphics with 16 low-power

execution units, 4K codec decode

Display Output

Triple independent display
1 x HDMI (up to 3840x2160 @ 60Hz)
1 x DisplayPort (up to 3840x2160 @ 60Hz)
1 x 18/24-bit dual-channel LVDS by CH7511B DP to LVDS
converter (up to 1920x1200 @ 60Hz)

Ethernet

LAN1: Intel

I219-LM PHY

LAN2: Intel

I211-AT PCIe GbE controller

Digital I/O

8-bit digital I/O by 10-pin (2x5) header

Super IO

Fintek F81866D-I

Embedded Controller

ITE IT8587VG

Audio

Realtek ALC662 HD codec

Watchdog Timer

Software programmable support 1~255 sec. system reset

Summary of Contents for NANO-ULT5




















































































































































Search results

Summary of Contents for NANO-ULT5

Reviews:

Related manuals for NANO-ULT5

Brands by name

Popular brands

IEI Technology NANO-ULT5, User Manual

Search results

Summary of Contents for NANO-ULT5

Reviews:

Related manuals for NANO-ULT5

Brands by name

Popular brands