manualshive.com logo in svg

IEI Technology NANO-ULT5, User Manual

Share
Download
IEI Technology NANO-ULT5 User Manual Download Page 102

 

 

NANO-ULT5 SBC 

 

Page 88 

 

Auto mode fan start temperature [40] 

  WARNING: 

Setting this value too high may cause the fan to rotate at full speed only 
when the CPU is at a very high temperature and therefore cause the 
system to be damaged. 

The 

Auto mode fan start temperature

 option can only be set if the 

CPU_FAN1 Smart 

Fan  Control

  option is set to 

Auto Mode

.  If the system  temperature  is  between 

Start 

Temperature

 and

 Off

 

Temperature

, the fan speed change to be 

Start PWM

. To set a 

value, select the 

Auto mode fan start temperature

 option and enter a decimal number 

between 1 and 100.   

 

Auto mode fan off temperature [30] 

  WARNING: 

Setting this value too high may cause the fan to speed up only when 
the CPU is at a very high temperature and therefore cause the system 
to be damaged. 

The 

Auto mode fan off temperature

 option can only be set if the 

CPU_FAN1 Smart Fan 

control

 option is set to 

Auto Mode

. If the system temperature is lower than

 Auto mode 

fan off temperature

, the fan speed change to be lowest. To set a value, select the 

Auto 

mode fan off temperature

 option and enter a decimal number between 1 and 100.   

 

Auto mode fan start PWM [30] 

The 

Auto mode fan start PWM

  option can only be set  if the 

CPU_FAN1  Smart Fan 

control

 option is set to 

Auto Mode

. Use the 

Auto mode fan start PWM

 option to set the 

PWM start value. To set a value, select the 

Auto mode fan start PWM

 option and enter a 

decimal number between 1 and 100.   

Summary of Contents for NANO-ULT5




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands