IEI Technology NANO-QM871-i1 User Manual Download

Page: 54 / 156

NANO-QM871-i1 EPIC SBC

Page 41

The NANO-QM871-i1 is equipped with two built-in RJ-45 Ethernet controllers. Each

controller can connect to the LAN through one RJ-45 LAN connector.

PIN

DESCRIPTION

PIN

DESCRIPTION

MDIA0+

MDIA2-

MDIA0-

MDIA1-

MDIA1+

MDIA3+

MDIA2+

MDIA3-

Table 3-27: LAN Pinouts

Figure 3-28: Ethernet Connector

LED Description

A on:

linked

blinking: data is being sent/received

off: 10 Mb/s

green: 100 Mb/s

orange: 1000 Mb/s

Table 3-28: Connector LEDs

3.3.2 HDMI Connectors

CN Label:

HDMI1, HDMI2

CN Type:

HDMI connector

CN Location:

CN Pinouts:

The HDMI connector connects to a display device with HDMI interface.

Pin Description Pin Description

1 HDM

GND

2 GND

HDMI_CLK#

Summary of Contents for NANO-QM871-i1





























































































































































Search results

Summary of Contents for NANO-QM871-i1

Reviews:

Related manuals for NANO-QM871-i1

Brands by name

Popular brands

IEI Technology NANO-QM871-i1, User Manual

Search results

Summary of Contents for NANO-QM871-i1

Reviews:

Related manuals for NANO-QM871-i1

Brands by name

Popular brands