IEI Technology NANO-QM871-i1-i7 User Manual Download Page 76

Page: 76 / 159

NANO-QM871-i1 EPIC SBC

Page 63

WARNING:

The diagram below is merely for illustration. The configuration and

connection of the cables from the TFT LCD screen being installed may

be different. Please refer to the installation manual that came with the

TFT LCD screen.

Figure 4-18: LVDS Connector

Step 3:

Locate the backlight inverter connector

. The location of the backlight inverter

connector is shown in

Chapter 3

Step 4:

Connect backlight connector

. Connect the backlight connector to the driver

TFT LCD PCB as shown in

Figure 4-19

. When inserting the cable connector,

make sure the pins are properly aligned.

Summary of Contents for NANO-QM871-i1-i7
































































































































































Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Related manuals for NANO-QM871-i1-i7

Brands by name

Popular brands

IEI Technology NANO-QM871-i1-i7, User Manual

Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Related manuals for NANO-QM871-i1-i7

Brands by name

Popular brands