manualshive.com logo in svg

IEI Technology NANO-QM871-i1-i7, User Manual

Share
Download
IEI Technology NANO-QM871-i1-i7 User Manual Download Page 54

 

 

NANO-QM871-i1 EPIC SBC 

Page 41

The NANO-QM871-i1 is equipped with two built-in RJ-45 Ethernet controllers. Each 

controller can connect to the LAN through one RJ-45 LAN connector. 

PIN 

DESCRIPTION 

PIN 

DESCRIPTION 

1 

MDIA0+ 

5 

MDIA2- 

2 

MDIA0- 

6 

MDIA1- 

3 

MDIA1+ 

7 

MDIA3+ 

4 

MDIA2+ 

8 

MDIA3- 

Table 3-27: LAN Pinouts 

 

 

Figure 3-28: Ethernet Connector 

 

LED Description 

LED Description 

A on: 

linked 

blinking: data is being sent/received 

B 

off: 10 Mb/s 

green: 100 Mb/s 

orange: 1000 Mb/s 

Table 3-28: Connector LEDs 

 

3.3.2 HDMI Connectors 

CN Label: 

HDMI1, HDMI2 

CN Type: 

HDMI connector 

CN Location: 

See 

Figure 3-27

 

CN Pinouts: 

See 

Table 3-29

 and 

Figure 3-29

 

The HDMI connector connects to a display device with HDMI interface. 

Pin Description  Pin Description 

1 HDM 

11 

GND 

2 GND 

12 

HDMI_CLK# 

Summary of Contents for NANO-QM871-i1-i7
































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands