IEI Technology NANO-QM871-i1-i7 User Manual Download Page 31

Page: 31 / 159

NANO-QM871-i1 EPIC SBC

Page 18

Connector

Type

Label

SPI Flash connector (EC)

2-pin header

CN1

TPM connector

20-pin header

TPM1

USB 2.0 connector

8-pin header

USB1

Table 3-1: Peripheral Interface Connectors

3.1.3 External Interface Panel Connectors

The table below lists the rear panel connectors on the NANO-QM871-i1. Detailed

descriptions of these connectors can be found in a later section.

Connector

Type

Label

Ethernet connectors

RJ-45

LAN1, LAN2

HDMI connectors

HDMI

HDMI1, HDMI2

USB 2.0 connector

USB 2.0

USB_CON2

USB 3.0 connector

USB 3.0

USB_CON1

VGA connector

DB-15

VGA1

Table 3-2: Rear Panel Connectors

3.2 Internal Peripheral Connectors

Internal peripheral connectors are found on the motherboard and are only accessible

when the motherboard is outside of the chassis. This section has complete descriptions of

all the internal, peripheral connectors on the NANO-QM871-i1.

3.2.1 Audio Connector

CN Label:

AUDIO1

CN Type:

10-pin header

CN Location:

CN Pinouts:

Summary of Contents for NANO-QM871-i1-i7
































































































































































Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Brands by name

Popular brands

IEI Technology NANO-QM871-i1-i7, User Manual

Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Brands by name

Popular brands