IEI Technology NANO-QM871-i1-i7 User Manual Download Page 24

Page: 24 / 159

NANO-QM871-i1 EPIC SBC

Page 11

2.1 Anti-static Precautions

WARNING!

Static electricity can destroy certain electronics. Make sure to follow the

ESD precautions to prevent damage to the product, and injury to the

user.

Make sure to adhere to the following guidelines:

Wear an anti-static wristband

: - Wearing an anti-static wristband can

prevent electrostatic discharge.

Self-grounding

:- Touch a grounded conductor every few minutes to

discharge any excess static buildup.

Use an anti-static pad

: When configuring any circuit board, place it on an

anti-static mat.

Only handle the edges of the PCB

:- Don't touch the surface of the

motherboard. Hold the motherboard by the edges when handling.

2.2 Unpacking Precautions

When the NANO-QM871-i1 is unpacked, please do the following:

Follow the antistatic guidelines above.

Make sure the packing box is facing upwards when opening.

Make sure all the packing list items are present.

Summary of Contents for NANO-QM871-i1-i7
































































































































































Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Brands by name

Popular brands

IEI Technology NANO-QM871-i1-i7, User Manual

Search results

Summary of Contents for NANO-QM871-i1-i7

Reviews:

Brands by name

Popular brands