IEI Technology Nano-PV-D4251 User Manual Download Page 45

Page: 45 / 153

NANO-PV-D4251/N4551/D5251 EPIC SBC

Page 32

9 Ground

(GND)

GND

Table 3-19: COM Connector Pinouts

3.2.18 Serial Port Connector (RS-232/422/485)

CN Label:

COM3

CN Type:

14-pin header (2x7)

CN Location:

See

Figure 3-19

CN Pinouts:

See

Table 3-20

Used for RS-232/422/485 communications.

Figure 3-19: Serial Port Connector Location

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

DCD

DSR2

RXD

RTS2

TXD

CTS2

DTR

RI2

GND

N/A

RS422 TX2/485+

RS422 TX2/485-

RS422 RX2+

RS422 RX2-

Table 3-20: Serial Port Connector Pinouts

3.2.19 SMBus Connector

CN Label:

CN1

CN Type:

4-pin wafer (1x4)

CN Location:

See

Figure 3-17

CN Pinouts:

See

Table 3-18

Summary of Contents for Nano-PV-D4251


























































































































































Search results

Summary of Contents for Nano-PV-D4251

Reviews:

Related manuals for Nano-PV-D4251

Brands by name

Popular brands

IEI Technology Nano-PV-D4251, User Manual

Search results

Summary of Contents for Nano-PV-D4251

Reviews:

Related manuals for Nano-PV-D4251

Brands by name

Popular brands