background image

 

 

MODAT-335A Field Service Terminal 

Page 17

3.1 Anti-static Precautions 

 WARNING: 

Failure to take ESD precautions during the maintenance of the 

MODAT-335A may result in permanent damage to the MODAT-335A 

and severe injury to the user. 

Electrostatic discharge (ESD) can cause serious damage to electronic components, 

including the MODAT-335A. Dry climates are especially susceptible to ESD. It is therefore 

critical that whenever the MODAT-335A is accessed internally, or any other electrical 

component is handled, the following anti-static precautions are strictly adhered to. 

ƒ

 

Wear an anti-static wristband

: - Wearing a simple anti-static wristband can 

help to prevent ESD from damaging the board. 

ƒ

 

Self-grounding

: - Before handling the board touch any grounded conducting 

material. During the time the board is handled, frequently touch any 

conducting materials that are connected to the ground. 

ƒ

 

Use an anti-static pad

: - When configuring the MODAT-335A, place it on an 

antic-static pad. This reduces the possibility of ESD damaging the 

MODAT-335A. 

ƒ

 

Only handle the edges of the PCB

: - When handling the PCB, hold the PCB 

by the edges. 

3.2 Installation Precautions 

When installing the MODAT-335A, please follow the precautions listed below: 

ƒ

 

Power turned off

: When installing the MODAT-335A, make sure the power is 

off. Failing to turn off the power may cause severe injury to the body and/or 

damage to the system. 

ƒ

 

Certified Engineers

: Only certified engineers should install and modify 

onboard functionalities.   

Summary of Contents for MODAT-335











































































Reviews: