IEI Technology KINO-QM770 User Manual Download Page 165

Page: 165 / 208

KINO-QM770 Mini-ITX SBC

Page 149

NOTE:

Use the following commands to check if the partitions were created

successfully.

Step 6:

Press any key to exit the recovery tool and automatically reboot the system.

Please continue to the following procedure: Build the Recovery Partition.

B.2.3 Install Operating System, Drivers and Applications

Install the operating system onto the unlabelled partition. The partition labeled "Recovery"

is for use by the system recovery tool and should not be used for installing the operating

system or any applications.

NOTE:

The operating system installation program may offer to reformat the

chosen partition. DO NOT format the partition again. The partition has

already been formatted and is ready for installing the new operating

system.

To install the operating system, insert the operating system installation CD into the optical

drive. Restart the computer and follow the installation instructions.

Summary of Contents for KINO-QM770

















































































































































































































Search results

Summary of Contents for KINO-QM770

Reviews:

IEI Technology KINO-QM770, User Manual, Page: 165 / 208

Search results

Summary of Contents for KINO-QM770

Reviews: