IEI Technology KINO-LX User Manual Download Page 192

Page: 192 / 197

Page 192

IEI® Technology, Corp

KINO-LX Motherboard

Step 2:

Step 1:

Step 2:

Step 1:

Step 2:

Confirm Delete

. The

Data on RAID drives will be erased (Y/N)

confirm box

appears. Press

Step 0:

E.4.6 Delete All RAID Setting & Partition

WARNING!

If a RAID configuration is deleted, all data previously stored on the member

drives of the RAID configuration will also be deleted.

Delete RAID Settings

. Use the arrow keys to highlight

Delete All RAID Setting

& Partition

and press

NTER

Confirm delete

. The

Data on RAID drives will be erased (Y/N)

confirm box

appears. Press

Step 0:

E.4.7 Rebuild RAID Array

The Rebuild RAID Array option can rebuild a RAID array if a member of a RAID

configuration should fail. Neither RAID 0 nor JBOD provides data redundancy. The

Rebuild RAID Array option only applies to RAID1 arrays and is applicable when a member

of a RAID1 configuration has failed.

Select Rebuild Array

. Use the arrow keys to highlight

Rebuild RAID Array

and

press

NTER

. A flashing ‘R’ appears in the list of existing arrays.

The source and

destination drives will be displayed.

Confirm rebuild array

. Press

to begin the rebuild process.

Step 0:

Summary of Contents for KINO-LX






































































































































































































Search results

Summary of Contents for KINO-LX

Reviews:

IEI Technology KINO-LX, User Manual, Page: 192 / 197

Search results

Summary of Contents for KINO-LX

Reviews: