IEI Technology KINO-LX User Manual Download Page 183

Page: 183 / 197

Page 183

KINO-LX Motherboard

CAUTION!

Do not accidentally disconnect the SATA drive cables. Carefully route the

cables within the chassis to avoid system down time.

E.2 Features and Benefits

Supports RAID levels 0, 1, and JBOD

Supports connectivity to two disk drives

Supported Operating Systems include: Windows 98/Me, Windows 2000 and

Windows XP

Windows-based software for RAID management

E.3 Accessing the ALi RAID Utility

To access the Ali RAID Utility, please follow the steps below:

Step 1:

Step 2:

Connect SATA drives to the system

. Connect two SATA drives to the system.

Make sure the drives have the same capacity, are the same type and have the

same speed.

Note:

Make sure the SATA drives are EXACTLY the same when they are

configured in a RAID configuration (JBOD, RAID 0 or RAID 1). If they are

not the same size, disk drive capacity is sacrificed and overall performance

affected.

Enable SATA drives in BIOS

. Start the computer and access the

Award BIOS

setup program. Next, open the

Advanced

menu. Enable the

SATA ROM

Support BIOS

option (see

Section 5.3

Summary of Contents for KINO-LX






































































































































































































Search results

Summary of Contents for KINO-LX

Reviews:

IEI Technology KINO-LX, User Manual, Page: 183 / 197

Search results

Summary of Contents for KINO-LX

Reviews: