IEI Technology KINO-LX User Manual Download Page 111

Page: 111 / 197

Page 111

KINO-LX Motherboard

Refresh Rate [60Hz]

The

Refresh Rate

option can only be configured if the

Flat Panel

Type

option is not set to

Auto

. Use the

Refresh Rate

option to set the screen refresh rate required by the panel

connected to the system. Check the documentation that came with the panel before

setting this option. The

Refresh Rate

options are:

60Hz (Default)

70Hz

72Hz

75Hz

85Hz

90Hz

100Hz

HSYNC Polarity [Low]

The

HSYNC Polarity

option can only be configured if the

Flat Panel

Type

option is not

set to

Auto

. Use the

HSYNC Polarity

option to set the polarity of the HSYNC signal to the

panel. The

HSYNC Polarity

options are:

High

Low (Default)

VSYNC Polarity Active [Low]

The

VGSYNC Polarity Active

option can only be configured if the

Flat Panel

Type

option

is not set to

Auto

. Use the

VGSYNC Polarity Active

option to set the polarity of the

VSYNC signal to the panel. The

VGSYNC Polarity Active

options are:

High

Low (Default)

Summary of Contents for KINO-LX






































































































































































































Search results

Summary of Contents for KINO-LX

Reviews:

IEI Technology KINO-LX, User Manual, Page: 111 / 197

Search results

Summary of Contents for KINO-LX

Reviews: