IEI Technology KINO-LX User Manual Download Page 108

Page: 108 / 197

Page 108

IEI® Technology, Corp

KINO-LX Motherboard

CAS Latency [Auto]

Use the

CAS Latency Time

option to set the Column Address Strobe (CAS) delay time.

The

CAS Latency Time

options are:

Auto (Default)

1.5 nanoseconds

2.0 nanoseconds

2.5 nanoseconds

3.0 nanoseconds

3.5 nanoseconds

Interleave Select [LOI]

Use the

Interleave Select

option to specify how the cache memory is interleaved.

LOI

(Default)

Low order interleaving (LOI) of memory occurs.

HOI

High order interleaving (HOI) of memory occurs.

Video Memory Size [8M]

Use the

Video Memory Size

option to determine how much memory is allocated to the

video graphics device. The

Video Memory Size

options are:

None

8M (Default)

16M

32M

64M

128M

254M

Output Display [CRT]

Use the

Output Display

configuration to specify the display devices the system is

connected to. The

Output Display

options are:

Flat Panel

Summary of Contents for KINO-LX






































































































































































































Search results

Summary of Contents for KINO-LX

Reviews:

IEI Technology KINO-LX, User Manual, Page: 108 / 197

Search results

Summary of Contents for KINO-LX

Reviews: