manualshive.com logo in svg

IEI Technology KINO-LX, User Manual, Page: 104 / 197

Share
Download
IEI Technology KINO-LX User Manual Download Page 104

 

 

Page 104 

 

IEI® Technology, Corp

.

 

KINO-LX Motherboard

 

Gate A20 Option [Fast] 

Use the 

Gate A20 Option

 option to set if the keyboard controller or the chipset controls 

the Gate A20 switching. 

 

Normal 

 

The keyboard controller does the switching. 

 

Fast 

(Default) 

The chipset does the switching. 

 

Typematic Rate Setting [Disabled] 

Use the 

Typematic Rate Setting

 configuration option to specify if only one character is 

allowed to appear on the screen if a key is continuously held down. When this option is 

enabled, the BIOS reports as before, but it then waits a moment, and, if the key is still held 

down, it begins to report that the key has been pressed repeatedly. This feature 

accelerates cursor movement with the arrow keys. 

 

Disabled 

(Default) 

Disables the typematic rate. 

 

Enabled 

 

Enables the typematic rate. 

 

Typematic Rate (Chars/sec) [6] 

The 

Typematic Rate

 option can only be configured if the 

Typematic Rate Setting

 is 

enabled. Use the 

Typematic Rate

 option to specify the rate keys are accelerated.   

 

6 

(Default) 

6 characters per second 

 

8 

 

8 characters per second 

 

10 

 

10 characters per second 

 

12 

 

12 characters per second 

 

15 

 

15 characters per second 

 

20 

 

20 characters per second 

 

24 

 

24 characters per second 

Summary of Contents for KINO-LX






































































































































































































Reviews:

No comments