manualshive.com logo in svg

IEI Technology KINO-KX Series, User Manual

Share
Download
IEI Technology KINO-KX Series User Manual Download Page 93

 

 

KINO-KX SBC 

 

Page 81 

 

Off 

 

Does not enable the keyboard Number Lock 

automatically. To use the 10-keys on the keyboard, 

press the Number Lock key located on the upper 

left-hand corner of the 10-key pad. The Number 

Lock LED on the keyboard lights up when the 

Number Lock is engaged. 

 

Quiet Boot [Enabled] 

Use the 

Quiet Boot

 BIOS option to select the screen display when the system boots. 

 

Disabled 

 

Normal POST messages displayed 

 

Enabled 

D

EFAULT

 

OEM Logo displayed instead of POST messages 

 

Launch PXE OpROM [Disabled] 

Use the 

Launch PXE OpROM 

option to enable or disable boot option for legacy network 

devices. 

 

Disabled 

D

EFAULT

 

Ignore all PXE Option ROMs 

 

Enabled 

 

Load PXE Option ROMs.   

 

Option ROM Messages [Force BIOS] 

Use the 

Option ROM Messages 

option to set the Option ROM display mode. 

 

Force 

BIOS 

D

EFAULT

 

Sets display mode to force BIOS. 

 

Keep 

Current 

 

Sets display mode to current. 

 

UEFI Boot [Disabled] 

Use the 

UEFI Boot 

option to enable or disable to boot from the UEFI devices. 

 

Enabled 

 

Boot from UEFI devices is enabled. 

Summary of Contents for KINO-KX Series















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands