manualshive.com logo in svg

IEI Technology KINO-ATOM, User Manual

Share
Download
IEI Technology KINO-ATOM User Manual Download Page 96

 

 

KINO-ATOM Motherboard

Page 78 

unit, the cooling fan of a power supply can also help generate airflow through the board 

surface.  

 NOTE: 

IEI has a wide range of backplanes available. Please contact your 

KINO-ATOM vendor, reseller or an IEI sales representative at 

3

[email protected]

 or visit the IEI website (

3

http://www.ieiworld.com.tw

) 

to find out more about the available chassis. 

5.7.2 Motherboard Installation 

To install the KINO-ATOM motherboard into the chassis please refer to the reference 

material that came with the chassis. 

5.8 Internal Peripheral Device Connections 

The cables listed in 

8

Table 5-8

 are shipped with the KINO-ATOM. 

Quantity 

Type 

1 

Keyboard and Mouse cable 

2 

SATA drive cable 

1 Power 

cable 

1 

Dual RS-232 cable 

Table 5-8: IEI Provided Cables 

Some optional items that can be purchased separately and installed on the KINO-ATOM 

include: 

 

Dual port USB cable 

 

Parallel port cable 

 

RS-232/422/485 cable 

 

ATX power cable 

 

HDTV out cable 

Summary of Contents for KINO-ATOM











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands