IEI Technology KINO-690S1 User Manual Download Page 60

Page: 60 / 229

KINO-690S1 Mini-ITX Motherboard

Page 42

The digital input/output connector is managed through a Super I/O chip. The DIO

connector pins are user programmable.

Figure 4-3: DIO Connector Connector Locations

PIN NO. DESCRIPTION

1 GND

2 VCC

3 Output

3 4 Output

5 Output

1 6 Output

7 Input

3 8 Input

9 Input

1 10

Input

Table 4-4: DIO Connector Connector Pinouts

4.2.3 Fan Connector (+12V)

CN Label:

CPU_FAN1, SYS_FAN1

CN Type:

3-pin header

CN Location:

See Figure 4-4

CN Pinouts:

See Table 4-5

The cooling fan connector provides a 12V, 500mA current to a system cooling fan. The

connector has a "rotation" pin to get rotation signals from fans and notify the system so the

Summary of Contents for KINO-690S1






































































































































































































































Search results

Summary of Contents for KINO-690S1

Reviews:

IEI Technology KINO-690S1, User Manual, Page: 60 / 229

Search results

Summary of Contents for KINO-690S1

Reviews: