IEI Technology KINO-690S1 User Manual Download Page 187

Page: 187 / 229

KINO-690S1 Mini-ITX Motherboard

Page 169

Figure 7-18: Location Browsing Window

Step 11:

Select the proper OS folder under the “

X:\3-LAN\BROADCOM BCM57xx

Drivers

” directory in the

Locate File

window, where “

X:\”

is the system CD

drive.

Step 12:

Click

PEN

and the driver is installed.

Step 0:

7.5 Realtek AC`97 Audio Driver (ALC655) Installation

To install the Realtek AC `97 audio driver, please follow the steps below.

7.5.1 BIOS Setup

Step 1:

Enter the BIOS setup. To do this, reboot the system and press

during POST.

Step 2:

Go to the Southbridge Configuration menu. Set the

Audio Controller

option to

[AC`97].

Step 3:

Press

F10

to save the changes and exit the BIOS setup. The system reboots.

Step 0:

7.5.2 Driver Installation

To install the audio driver please follow the steps below.

Step 1:

Select

AUDIO

from the list in

Figure 7-2

Step 2:

A new window opens (Figure 7-19).

Summary of Contents for KINO-690S1






































































































































































































































Search results

Summary of Contents for KINO-690S1

Reviews:

IEI Technology KINO-690S1, User Manual, Page: 187 / 229

Search results

Summary of Contents for KINO-690S1

Reviews: