IEI Technology KINO-690S1 User Manual Download Page 140

Page: 140 / 229

KINO-690S1 Mini-ITX Motherboard

Page 122

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded onto the system.

Disabled

Legacy USB support disabled

Enabled D

EFAULT

Legacy USB support enabled

Auto

Legacy USB support disabled if no USB devices are

connected

USB2.0 Controller Mode [HiSpeed]

Use the

USB2.0 Controller Mode

option to set the speed of the USB2.0 controller.

FullSpeed

The controller is capable of operating at 12Mb/s

HiSpeed D

EFAULT

The controller is capable of operating at 480Mb/s

6.3.8.1 USB Mass Storage Device Configuration

NOTE:

This option is only available if a USB drive is inserted into the USB port.

Use the USB Mass Storage Device Configuration menu (BIOS Menu 12) to configure USB

mass storage class devices.

Summary of Contents for KINO-690S1






































































































































































































































Search results

Summary of Contents for KINO-690S1

Reviews:

IEI Technology KINO-690S1, User Manual, Page: 140 / 229

Search results

Summary of Contents for KINO-690S1

Reviews: