IEI Technology KINO-690S1 User Manual Download Page 133

Page: 133 / 229

KINO-690S1 Mini-ITX Motherboard

Page 115

Use the ACPI Version Features option to select the ACPI (Advanced Configuration and

Power Interface Specification) version to run on the system.

ACPI v1.0

(Default)

ACPI revision 1.0 runs on the system

ACPI v2.0

ACPI revision 1.0 runs on the system

ACPI v3.0

ACPI revision 1.0 runs on the system

Suspend Mode [S1(POS)]

The

Suspend Mode

BIOS option specifies the sleep state your system will enter when it

is not being used.

S1 (POS)

(Default)

System appears off. The CPU is stopped; RAM is refreshed;

the system is running in a low power mode.

S3 (STR)

System appears off. The CPU has no power; RAM is in slow

refresh; the power supply is in a reduced power mode.

Auto

The system automatically determines the system sleep state.

6.3.6 Trusted Computing

Use the

Trusted Computing

menu (

BIOS Menu 9

) to configure settings related to the

Trusted Computing Group (TCG) Trusted Platform Module (TPM).

Summary of Contents for KINO-690S1






































































































































































































































Search results

Summary of Contents for KINO-690S1

Reviews:

IEI Technology KINO-690S1, User Manual, Page: 133 / 229

Search results

Summary of Contents for KINO-690S1

Reviews: