IEI Technology ISIGNAGER - 800WL-N270 Page 10 User Manual Download

Page: 10 / 67

iSignager-800WL-N270 Digital Signage Player

Page 2

1.1 Important Notice

NOTE:

This iSignager-800WL-N270 user manual only contains the hardware information.

For the detailed information of the iSignager AdMinistrator software, please refer to

the iSignager AdMinistrator user manual.

1.2 iSignager-800WL-N270 Overview

The iSignager-800WL-N270 is a multimedia device developed by IEI to design and display

dynamic, visual and audio contents for a target audience. The user can update the display

sources anytime anywhere. With the iSignager-800WL-N270 an advertising station is

easily established and promotes the product and services in the simplest way.

Summary of Contents for ISIGNAGER - 800WL-N270




































































Search results

Summary of Contents for ISIGNAGER - 800WL-N270

Reviews:

Related manuals for ISIGNAGER - 800WL-N270

Brands by name

Popular brands

IEI Technology ISIGNAGER - 800WL-N270, User Manual

Search results

Summary of Contents for ISIGNAGER - 800WL-N270

Reviews:

Related manuals for ISIGNAGER - 800WL-N270

Brands by name

Popular brands