manualshive.com logo in svg

IEI Technology ISDM-084G, User Manual

Share
Download
IEI Technology ISDM-084G User Manual Download Page 93

 

 

ISDM Series Industrial Monitor 

Page 93 

5.2 Unpacking 

5.2.1 Packaging 

When shipped, the ISDM series industrial monitor is wrapped in a plastic bag. Two 

polystyrene ends are placed on either side of the monitor. The monitor is then placed into 

a first (internal) cardboard box. This box is then sealed and placed into a second (external) 

cardboard box. The second box is also sealed. A bag containing accessory items is 

placed underneath the monitor, at the bottom of the internal (first) box. 

5.2.2 Unpacking Procedure 

To unpack the ISDM series industrial monitor, follow the steps below: 

 WARNING: 

The front side LCD screen has a protective plastic cover stuck to the 

screen. Only remove the plastic cover after the ISDM series industrial 

monitor has been properly installed. This ensures the screen is protected 

during the installation process. 

Step 1: 

Use box cutters, a knife or a sharp pair of scissors that seals the top side of the 

external (second) box. 

Step 2: 

Open the external (second) box. 

Step 3: 

Use box cutters, a knife or a sharp pair of scissors that seals the top side of the 

internal (first) box. 

Step 4: 

Lift the monitor out of the boxes. 

Step 5: 

Remove both polystyrene ends, one from each side. 

Step 6: 

Pull the plastic cover off the ISDM series industrial monitor. 

Summary of Contents for ISDM-084G

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands