IEI Technology IMBA-H110 User Manual Download Page 108

Page: 108 / 152

IMBA-H110 ATX Motherboard

Page 94



CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control [Auto Mode]

Use the

CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control

option to

configure the CPU/System Smart Fan.



Auto Mode

EFAULT

The fan adjusts its speed using Auto Mode
settings.



Manual Mode

The fan spins at the speed set in Manual Mode
settings.



Auto mode fan start/off temperature

Use the + or – key to change the

Auto mode fan start/off temperature

value. Enter a

decimal number between 1 and 100.



Auto mode fan start PWM

Use the + or – key to change the

Auto mode fan start PWM

value. Enter a decimal

number between 1 and 100.



Auto mode fan slope PWM

Use the + or – key to change the

Auto mode fan slope PWM

value. Enter a decimal

number between 1 and 8.

5.3.5 RTC Wake Settings

The

RTC Wake Settings

menu (

BIOS Menu 10

) enables the system to wake at the

specified time.

Summary of Contents for IMBA-H110

























































































































































Search results

Summary of Contents for IMBA-H110

Reviews:

Brands by name

Popular brands

IEI Technology IMBA-H110, User Manual

Search results

Summary of Contents for IMBA-H110

Reviews:

Brands by name

Popular brands