IEI Technology IceCare-10W series User Manual Download Page 71

Page: 71 / 107

ICECARE-10W Mobile Sales Assistant

Page 59

5.3.7 USB Configuration

Use the

USB Configuration

menu (

583

BIOS Menu 9

) to read USB configuration information

and configure the USB settings.

Advanced

USB Configuration

USB Devices:
1 Keyboard

Legacy USB Support

[Enabled]

Mass Storage Devices:

Generic STORAGE DEVICE 0207

[Auto]

Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.

---------------------



: Select Screen





: Select Item

Enter

Select

F1 General

Help

F2 Previous

Values

F3 Optimized
Defaults
F4 Save

ESC Exit

BIOS Menu 9: USB Configuration



USB Devices

The

USB Devices Enabled

field lists the USB devices that are enabled on the system



Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB

keyboard can control the system even when there is no USB driver loaded onto the

system.



Enabled D

EFAULT

Legacy USB support enabled

Summary of Contents for IceCare-10W series












































































































Search results

Summary of Contents for IceCare-10W series

Reviews:

Related manuals for IceCare-10W series

Brands by name

Popular brands

IEI Technology IceCare-10W series, User Manual

Search results

Summary of Contents for IceCare-10W series

Reviews:

Related manuals for IceCare-10W series

Brands by name

Popular brands